product datasheet minnie-assembly series ordering number description family type led color diameter height style optic material holder material fastening status ca12239 ca12239_minnie-m-mtg minnie reflector mt-g black 35 mm 15.4 mm round pc pc tape ready fwhm efficiency cd/lm gerber file 26 degrees - - available ordering number description family type led color diameter height style optic material holder material fastening status ca12096 ca12096_minnie-w-mtg minnie reflector mt-g black 35 mm 15.4 mm round pc pc tape ready fwhm efficiency cd/lm gerber file 36 degrees - - available ordering number description family type led color diameter height style optic material holder material fastening status CA12240 CA12240_minnie-www-mtg minnie reflector mt-g black 35 mm 15.4 mm round pc pc tape ready fwhm efficiency cd/lm gerber file 74 degrees - - available note: the typical divergence will be changed by different color, chip size and chip position tolerance. the typical total divergence is the full angle measured where the luminous intensity is half of the peak value. october 6th 2011 22:57 copyright ledil oy - subject to change without prior notice - page 1/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet minnie-assembly series general information - product series especially designed & optimized for mt-g series of leds. - special care taken to make light distribution as uniform as possible. - reflector is made of aluminium coated pc (120 degrees of celcius / 248 degrees of fahrenheit) with protective lacquer (110 degrees of celcius / 230 degrees of fahrenheit). - optic holder molded by high quality pc material (120 dergees of celcius / 248 degrees of fahrenheit). - fastening to heat sink with a pu foam adhesive tape of automotive grade. please find fastening details by clicking link: http://www.ledil.com/datasheets/datasheet_tape.pdf note 1: we advise customer to ensure the suitability and sufficiency of the bond in the end product. for example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the tape. note 2: assembly to the surface must be made straight, so the tape bonds constant and balanced with fastening surface. slanted assembly might cause unbalanced bond to the surface. all surfaces where tape is applied must be clean, dry and free from grease and dirt. if cleaning of pcb surfaces is needed, please follow strictly the cleaning instructions of your led manufacturer - this is important as cleaning shall under no circumstances damage leds or other electronics components on the pcb. further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. october 6th 2011 22:57 copyright ledil oy - subject to change without prior notice - page 2/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet minnie-assembly series ca12096 ca12239 CA12240 october 6th 2011 22:57 copyright ledil oy - subject to change without prior notice - page 3/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 0% 25% 50% 75% 100% -60 -50 -40 -30 -20 -10 0 10 20 30 40 50 60 relative intensity of CA12240_minnie - www - mtg - assy 0% 25% 50% 75% 100% -50 -40 -30 -20 -10 0 10 20 30 40 50 relative intensity of ca12239_minnie - m - mtg - assy 0 % 25 % 50 % 75 % 100 % -60 -50 -40 -30 -20 -10 0 10 20 30 40 50 60 relative intensity of minnie - w - mtg a d b c a d 3 2 3 2 4 1 4 1 designed by hh date 01.01.2011 checked by hh date 18.02.2011 drawn by mav date 18.02.2011 this drawing is our property. it can't be reproduced or communicated without our written agreement. scale 1:1 weight(g) sheet 1/1 size a4 drawing number rev 1 drawing title datasheet minnie mt-g reflector assy ledil oy tehdaskatu 13 fin-24100 salo finland materials: reflector: pc with metal coating and clear laquer holder: pc, color black tape: pu foam with psa-adhesive tape holder reflector 15.8 35 26.9 9.3 9.3
product datasheet minnie-assembly series ordering number description family type led color diameter height style optic material holder material fastening status ca12239 ca12239_minnie-m-mtg minnie reflector mt-g black 35 mm 15.4 mm round pc pc tape ready fwhm efficiency cd/lm gerber file 26 degrees - - available ordering number description family type led color diameter height style optic material holder material fastening status ca12096 ca12096_minnie-w-mtg minnie reflector mt-g black 35 mm 15.4 mm round pc pc tape ready fwhm efficiency cd/lm gerber file 36 degrees - - available ordering number description family type led color diameter height style optic material holder material fastening status CA12240 CA12240_minnie-www-mtg minnie reflector mt-g black 35 mm 15.4 mm round pc pc tape ready fwhm efficiency cd/lm gerber file 74 degrees - - available note: the typical divergence will be changed by different color, chip size and chip position tolerance. the typical total divergence is the full angle measured where the luminous intensity is half of the peak value. october 6th 2011 22:57 copyright ledil oy - subject to change without prior notice - page 1/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet minnie-assembly series general information - product series especially designed & optimized for mt-g series of leds. - special care taken to make light distribution as uniform as possible. - reflector is made of aluminium coated pc (120 degrees of celcius / 248 degrees of fahrenheit) with protective lacquer (110 degrees of celcius / 230 degrees of fahrenheit). - optic holder molded by high quality pc material (120 dergees of celcius / 248 degrees of fahrenheit). - fastening to heat sink with a pu foam adhesive tape of automotive grade. please find fastening details by clicking link: http://www.ledil.com/datasheets/datasheet_tape.pdf note 1: we advise customer to ensure the suitability and sufficiency of the bond in the end product. for example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the tape. note 2: assembly to the surface must be made straight, so the tape bonds constant and balanced with fastening surface. slanted assembly might cause unbalanced bond to the surface. all surfaces where tape is applied must be clean, dry and free from grease and dirt. if cleaning of pcb surfaces is needed, please follow strictly the cleaning instructions of your led manufacturer - this is important as cleaning shall under no circumstances damage leds or other electronics components on the pcb. further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. october 6th 2011 22:57 copyright ledil oy - subject to change without prior notice - page 2/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet minnie-assembly series ca12096 ca12239 CA12240 october 6th 2011 22:57 copyright ledil oy - subject to change without prior notice - page 3/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 0% 25% 50% 75% 100% -60 -50 -40 -30 -20 -10 0 10 20 30 40 50 60 relative intensity of CA12240_minnie - www - mtg - assy 0% 25% 50% 75% 100% -50 -40 -30 -20 -10 0 10 20 30 40 50 relative intensity of ca12239_minnie - m - mtg - assy 0 % 25 % 50 % 75 % 100 % -60 -50 -40 -30 -20 -10 0 10 20 30 40 50 60 relative intensity of minnie - w - mtg a d b c a d 3 2 3 2 4 1 4 1 designed by hh date 01.01.2011 checked by hh date 18.02.2011 drawn by mav date 18.02.2011 this drawing is our property. it can't be reproduced or communicated without our written agreement. scale 1:1 weight(g) sheet 1/1 size a4 drawing number rev 1 drawing title datasheet minnie mt-g reflector assy ledil oy tehdaskatu 13 fin-24100 salo finland materials: reflector: pc with metal coating and clear laquer holder: pc, color black tape: pu foam with psa-adhesive tape holder reflector 15.8 35 26.9 9.3 9.3
product datasheet minnie-assembly series ordering number description family type led color diameter height style optic material holder material fastening status ca12239 ca12239_minnie-m-mtg minnie reflector mt-g black 35 mm 15.4 mm round pc pc tape ready fwhm efficiency cd/lm gerber file 26 degrees - - available ordering number description family type led color diameter height style optic material holder material fastening status ca12096 ca12096_minnie-w-mtg minnie reflector mt-g black 35 mm 15.4 mm round pc pc tape ready fwhm efficiency cd/lm gerber file 36 degrees - - available ordering number description family type led color diameter height style optic material holder material fastening status CA12240 CA12240_minnie-www-mtg minnie reflector mt-g black 35 mm 15.4 mm round pc pc tape ready fwhm efficiency cd/lm gerber file 74 degrees - - available note: the typical divergence will be changed by different color, chip size and chip position tolerance. the typical total divergence is the full angle measured where the luminous intensity is half of the peak value. october 6th 2011 22:57 copyright ledil oy - subject to change without prior notice - page 1/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet minnie-assembly series general information - product series especially designed & optimized for mt-g series of leds. - special care taken to make light distribution as uniform as possible. - reflector is made of aluminium coated pc (120 degrees of celcius / 248 degrees of fahrenheit) with protective lacquer (110 degrees of celcius / 230 degrees of fahrenheit). - optic holder molded by high quality pc material (120 dergees of celcius / 248 degrees of fahrenheit). - fastening to heat sink with a pu foam adhesive tape of automotive grade. please find fastening details by clicking link: http://www.ledil.com/datasheets/datasheet_tape.pdf note 1: we advise customer to ensure the suitability and sufficiency of the bond in the end product. for example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the tape. note 2: assembly to the surface must be made straight, so the tape bonds constant and balanced with fastening surface. slanted assembly might cause unbalanced bond to the surface. all surfaces where tape is applied must be clean, dry and free from grease and dirt. if cleaning of pcb surfaces is needed, please follow strictly the cleaning instructions of your led manufacturer - this is important as cleaning shall under no circumstances damage leds or other electronics components on the pcb. further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. october 6th 2011 22:57 copyright ledil oy - subject to change without prior notice - page 2/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet minnie-assembly series ca12096 ca12239 CA12240 october 6th 2011 22:57 copyright ledil oy - subject to change without prior notice - page 3/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 0% 25% 50% 75% 100% -60 -50 -40 -30 -20 -10 0 10 20 30 40 50 60 relative intensity of CA12240_minnie - www - mtg - assy 0% 25% 50% 75% 100% -50 -40 -30 -20 -10 0 10 20 30 40 50 relative intensity of ca12239_minnie - m - mtg - assy 0 % 25 % 50 % 75 % 100 % -60 -50 -40 -30 -20 -10 0 10 20 30 40 50 60 relative intensity of minnie - w - mtg a d b c a d 3 2 3 2 4 1 4 1 designed by hh date 01.01.2011 checked by hh date 18.02.2011 drawn by mav date 18.02.2011 this drawing is our property. it can't be reproduced or communicated without our written agreement. scale 1:1 weight(g) sheet 1/1 size a4 drawing number rev 1 drawing title datasheet minnie mt-g reflector assy ledil oy tehdaskatu 13 fin-24100 salo finland materials: reflector: pc with metal coating and clear laquer holder: pc, color black tape: pu foam with psa-adhesive tape holder reflector 15.8 35 26.9 9.3 9.3
product datasheet minnie-assembly series ordering number description family type led color diameter height style optic material holder material fastening status ca12239 ca12239_minnie-m-mtg minnie reflector mt-g black 35 mm 15.4 mm round pc pc tape ready fwhm efficiency cd/lm gerber file 26 degrees - - available ordering number description family type led color diameter height style optic material holder material fastening status ca12096 ca12096_minnie-w-mtg minnie reflector mt-g black 35 mm 15.4 mm round pc pc tape ready fwhm efficiency cd/lm gerber file 36 degrees - - available ordering number description family type led color diameter height style optic material holder material fastening status CA12240 CA12240_minnie-www-mtg minnie reflector mt-g black 35 mm 15.4 mm round pc pc tape ready fwhm efficiency cd/lm gerber file 74 degrees - - available note: the typical divergence will be changed by different color, chip size and chip position tolerance. the typical total divergence is the full angle measured where the luminous intensity is half of the peak value. october 6th 2011 22:57 copyright ledil oy - subject to change without prior notice - page 1/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet minnie-assembly series general information - product series especially designed & optimized for mt-g series of leds. - special care taken to make light distribution as uniform as possible. - reflector is made of aluminium coated pc (120 degrees of celcius / 248 degrees of fahrenheit) with protective lacquer (110 degrees of celcius / 230 degrees of fahrenheit). - optic holder molded by high quality pc material (120 dergees of celcius / 248 degrees of fahrenheit). - fastening to heat sink with a pu foam adhesive tape of automotive grade. please find fastening details by clicking link: http://www.ledil.com/datasheets/datasheet_tape.pdf note 1: we advise customer to ensure the suitability and sufficiency of the bond in the end product. for example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the tape. note 2: assembly to the surface must be made straight, so the tape bonds constant and balanced with fastening surface. slanted assembly might cause unbalanced bond to the surface. all surfaces where tape is applied must be clean, dry and free from grease and dirt. if cleaning of pcb surfaces is needed, please follow strictly the cleaning instructions of your led manufacturer - this is important as cleaning shall under no circumstances damage leds or other electronics components on the pcb. further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. october 6th 2011 22:57 copyright ledil oy - subject to change without prior notice - page 2/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet minnie-assembly series ca12096 ca12239 CA12240 october 6th 2011 22:57 copyright ledil oy - subject to change without prior notice - page 3/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 0% 25% 50% 75% 100% -60 -50 -40 -30 -20 -10 0 10 20 30 40 50 60 relative intensity of CA12240_minnie - www - mtg - assy 0% 25% 50% 75% 100% -50 -40 -30 -20 -10 0 10 20 30 40 50 relative intensity of ca12239_minnie - m - mtg - assy 0 % 25 % 50 % 75 % 100 % -60 -50 -40 -30 -20 -10 0 10 20 30 40 50 60 relative intensity of minnie - w - mtg a d b c a d 3 2 3 2 4 1 4 1 designed by hh date 01.01.2011 checked by hh date 18.02.2011 drawn by mav date 18.02.2011 this drawing is our property. it can't be reproduced or communicated without our written agreement. scale 1:1 weight(g) sheet 1/1 size a4 drawing number rev 1 drawing title datasheet minnie mt-g reflector assy ledil oy tehdaskatu 13 fin-24100 salo finland materials: reflector: pc with metal coating and clear laquer holder: pc, color black tape: pu foam with psa-adhesive tape holder reflector 15.8 35 26.9 9.3 9.3
product datasheet minnie-assembly series ordering number description family type led color diameter height style optic material holder material fastening status ca12239 ca12239_minnie-m-mtg minnie reflector mt-g black 35 mm 15.4 mm round pc pc tape ready fwhm efficiency cd/lm gerber file 26 degrees - - available ordering number description family type led color diameter height style optic material holder material fastening status ca12096 ca12096_minnie-w-mtg minnie reflector mt-g black 35 mm 15.4 mm round pc pc tape ready fwhm efficiency cd/lm gerber file 36 degrees - - available ordering number description family type led color diameter height style optic material holder material fastening status CA12240 CA12240_minnie-www-mtg minnie reflector mt-g black 35 mm 15.4 mm round pc pc tape ready fwhm efficiency cd/lm gerber file 74 degrees - - available note: the typical divergence will be changed by different color, chip size and chip position tolerance. the typical total divergence is the full angle measured where the luminous intensity is half of the peak value. october 6th 2011 22:57 copyright ledil oy - subject to change without prior notice - page 1/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet minnie-assembly series general information - product series especially designed & optimized for mt-g series of leds. - special care taken to make light distribution as uniform as possible. - reflector is made of aluminium coated pc (120 degrees of celcius / 248 degrees of fahrenheit) with protective lacquer (110 degrees of celcius / 230 degrees of fahrenheit). - optic holder molded by high quality pc material (120 dergees of celcius / 248 degrees of fahrenheit). - fastening to heat sink with a pu foam adhesive tape of automotive grade. please find fastening details by clicking link: http://www.ledil.com/datasheets/datasheet_tape.pdf note 1: we advise customer to ensure the suitability and sufficiency of the bond in the end product. for example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the tape. note 2: assembly to the surface must be made straight, so the tape bonds constant and balanced with fastening surface. slanted assembly might cause unbalanced bond to the surface. all surfaces where tape is applied must be clean, dry and free from grease and dirt. if cleaning of pcb surfaces is needed, please follow strictly the cleaning instructions of your led manufacturer - this is important as cleaning shall under no circumstances damage leds or other electronics components on the pcb. further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. october 6th 2011 22:57 copyright ledil oy - subject to change without prior notice - page 2/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet minnie-assembly series ca12096 ca12239 CA12240 october 6th 2011 22:57 copyright ledil oy - subject to change without prior notice - page 3/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 0% 25% 50% 75% 100% -60 -50 -40 -30 -20 -10 0 10 20 30 40 50 60 relative intensity of CA12240_minnie - www - mtg - assy 0% 25% 50% 75% 100% -50 -40 -30 -20 -10 0 10 20 30 40 50 relative intensity of ca12239_minnie - m - mtg - assy 0 % 25 % 50 % 75 % 100 % -60 -50 -40 -30 -20 -10 0 10 20 30 40 50 60 relative intensity of minnie - w - mtg a d b c a d 3 2 3 2 4 1 4 1 designed by hh date 01.01.2011 checked by hh date 18.02.2011 drawn by mav date 18.02.2011 this drawing is our property. it can't be reproduced or communicated without our written agreement. scale 1:1 weight(g) sheet 1/1 size a4 drawing number rev 1 drawing title datasheet minnie mt-g reflector assy ledil oy tehdaskatu 13 fin-24100 salo finland materials: reflector: pc with metal coating and clear laquer holder: pc, color black tape: pu foam with psa-adhesive tape holder reflector 15.8 35 26.9 9.3 9.3
product datasheet minnie-assembly series ordering number description family type led color diameter height style optic material holder material fastening status ca12239 ca12239_minnie-m-mtg minnie reflector mt-g black 35 mm 15.4 mm round pc pc tape ready fwhm efficiency cd/lm gerber file 26 degrees - - available ordering number description family type led color diameter height style optic material holder material fastening status ca12096 ca12096_minnie-w-mtg minnie reflector mt-g black 35 mm 15.4 mm round pc pc tape ready fwhm efficiency cd/lm gerber file 36 degrees - - available ordering number description family type led color diameter height style optic material holder material fastening status CA12240 CA12240_minnie-www-mtg minnie reflector mt-g black 35 mm 15.4 mm round pc pc tape ready fwhm efficiency cd/lm gerber file 74 degrees - - available note: the typical divergence will be changed by different color, chip size and chip position tolerance. the typical total divergence is the full angle measured where the luminous intensity is half of the peak value. october 6th 2011 22:57 copyright ledil oy - subject to change without prior notice - page 1/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet minnie-assembly series general information - product series especially designed & optimized for mt-g series of leds. - special care taken to make light distribution as uniform as possible. - reflector is made of aluminium coated pc (120 degrees of celcius / 248 degrees of fahrenheit) with protective lacquer (110 degrees of celcius / 230 degrees of fahrenheit). - optic holder molded by high quality pc material (120 dergees of celcius / 248 degrees of fahrenheit). - fastening to heat sink with a pu foam adhesive tape of automotive grade. please find fastening details by clicking link: http://www.ledil.com/datasheets/datasheet_tape.pdf note 1: we advise customer to ensure the suitability and sufficiency of the bond in the end product. for example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the tape. note 2: assembly to the surface must be made straight, so the tape bonds constant and balanced with fastening surface. slanted assembly might cause unbalanced bond to the surface. all surfaces where tape is applied must be clean, dry and free from grease and dirt. if cleaning of pcb surfaces is needed, please follow strictly the cleaning instructions of your led manufacturer - this is important as cleaning shall under no circumstances damage leds or other electronics components on the pcb. further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. october 6th 2011 22:57 copyright ledil oy - subject to change without prior notice - page 2/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet minnie-assembly series ca12096 ca12239 CA12240 october 6th 2011 22:57 copyright ledil oy - subject to change without prior notice - page 3/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 0% 25% 50% 75% 100% -60 -50 -40 -30 -20 -10 0 10 20 30 40 50 60 relative intensity of CA12240_minnie - www - mtg - assy 0% 25% 50% 75% 100% -50 -40 -30 -20 -10 0 10 20 30 40 50 relative intensity of ca12239_minnie - m - mtg - assy 0 % 25 % 50 % 75 % 100 % -60 -50 -40 -30 -20 -10 0 10 20 30 40 50 60 relative intensity of minnie - w - mtg a d b c a d 3 2 3 2 4 1 4 1 designed by hh date 01.01.2011 checked by hh date 18.02.2011 drawn by mav date 18.02.2011 this drawing is our property. it can't be reproduced or communicated without our written agreement. scale 1:1 weight(g) sheet 1/1 size a4 drawing number rev 1 drawing title datasheet minnie mt-g reflector assy ledil oy tehdaskatu 13 fin-24100 salo finland materials: reflector: pc with metal coating and clear laquer holder: pc, color black tape: pu foam with psa-adhesive tape holder reflector 15.8 35 26.9 9.3 9.3
product datasheet minnie-assembly series ordering number description family type led color diameter height style optic material holder material fastening status ca12239 ca12239_minnie-m-mtg minnie reflector mt-g black 35 mm 15.4 mm round pc pc tape ready fwhm efficiency cd/lm gerber file 26 degrees - - available ordering number description family type led color diameter height style optic material holder material fastening status ca12096 ca12096_minnie-w-mtg minnie reflector mt-g black 35 mm 15.4 mm round pc pc tape ready fwhm efficiency cd/lm gerber file 36 degrees - - available ordering number description family type led color diameter height style optic material holder material fastening status CA12240 CA12240_minnie-www-mtg minnie reflector mt-g black 35 mm 15.4 mm round pc pc tape ready fwhm efficiency cd/lm gerber file 74 degrees - - available note: the typical divergence will be changed by different color, chip size and chip position tolerance. the typical total divergence is the full angle measured where the luminous intensity is half of the peak value. october 6th 2011 22:57 copyright ledil oy - subject to change without prior notice - page 1/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet minnie-assembly series general information - product series especially designed & optimized for mt-g series of leds. - special care taken to make light distribution as uniform as possible. - reflector is made of aluminium coated pc (120 degrees of celcius / 248 degrees of fahrenheit) with protective lacquer (110 degrees of celcius / 230 degrees of fahrenheit). - optic holder molded by high quality pc material (120 dergees of celcius / 248 degrees of fahrenheit). - fastening to heat sink with a pu foam adhesive tape of automotive grade. please find fastening details by clicking link: http://www.ledil.com/datasheets/datasheet_tape.pdf note 1: we advise customer to ensure the suitability and sufficiency of the bond in the end product. for example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the tape. note 2: assembly to the surface must be made straight, so the tape bonds constant and balanced with fastening surface. slanted assembly might cause unbalanced bond to the surface. all surfaces where tape is applied must be clean, dry and free from grease and dirt. if cleaning of pcb surfaces is needed, please follow strictly the cleaning instructions of your led manufacturer - this is important as cleaning shall under no circumstances damage leds or other electronics components on the pcb. further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. october 6th 2011 22:57 copyright ledil oy - subject to change without prior notice - page 2/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet minnie-assembly series ca12096 ca12239 CA12240 october 6th 2011 22:57 copyright ledil oy - subject to change without prior notice - page 3/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 0% 25% 50% 75% 100% -60 -50 -40 -30 -20 -10 0 10 20 30 40 50 60 relative intensity of CA12240_minnie - www - mtg - assy 0% 25% 50% 75% 100% -50 -40 -30 -20 -10 0 10 20 30 40 50 relative intensity of ca12239_minnie - m - mtg - assy 0 % 25 % 50 % 75 % 100 % -60 -50 -40 -30 -20 -10 0 10 20 30 40 50 60 relative intensity of minnie - w - mtg a d b c a d 3 2 3 2 4 1 4 1 designed by hh date 01.01.2011 checked by hh date 18.02.2011 drawn by mav date 18.02.2011 this drawing is our property. it can't be reproduced or communicated without our written agreement. scale 1:1 weight(g) sheet 1/1 size a4 drawing number rev 1 drawing title datasheet minnie mt-g reflector assy ledil oy tehdaskatu 13 fin-24100 salo finland materials: reflector: pc with metal coating and clear laquer holder: pc, color black tape: pu foam with psa-adhesive tape holder reflector 15.8 35 26.9 9.3 9.3
|
